11 of 13 verified on hardwareLR11xx 1 SX126x 8 SX127x 4 SX128x 2
Supported devices
One firmware, 13 boards, four radio families. Every page below is generated from the firmware's own board registry and pin headers, so it says what the code actually does on that hardware — including the parts that are fitted and left alone, and the boards no bench has powered on yet.
LilyGO T3-S3 v1.2/v1.3 (SX1262 or SX1276/78)
t3s3- MCU
- ESP32-S3FH4R2: 4 MB flash, 2 MB PSRAM
- Radio
- SX1276/78 or SX1262 — detected at boot
- Panel
- 0.96" SSD1306 (I²C)
Verified (sx1276), sx1262 expected
Generic ESP32-S3 DevKitC-1 + SX1262 module
esp32s3-qspi- MCU
- ESP32-S3: 8 MB flash, quad PSRAM
- Radio
- SX1262
- Panel
- optional SSD1306
Builds — wire the module per the flags
LilyGO T-Beam v1.1/v1.2 (SX1276 or SX1262)
tbeam- MCU
- ESP32: 4 MB flash, 4 MB PSRAM
- Radio
- SX1276 (v1.1) or SX1262 (v1.2) — detected at boot
- Panel
- 0.96" SSD1306 (I²C)
Verified on hardware
LilyGO T-Beam Supreme
tbeam-supreme- MCU
- ESP32-S3FN8: 8 MB flash, 8 MB quad PSRAM
- Radio
- SX1262 in a socketed module (TCXO at 1.8 V, DIO2 drives the RF switch)
- Panel
- 1.3" 128x64 SH1106 (I²C) — not the SSD1306 the other OLED boards carry
Verified on hardware
LilyGO T3-S3 with SX1280 (2.4 GHz)
t3s3-sx1280- MCU
- ESP32-S3FH4R2: 4 MB flash, 2 MB PSRAM
- Radio
- SX1280
- Panel
- 0.96" SSD1306
Verified on hardware
LilyGO T3-S3 with SX1280 + PA (2.4 GHz)
t3s3-sx1280-pa- MCU
- ESP32-S3FH4R2: 4 MB flash, 2 MB PSRAM
- Radio
- SX1280 + PA
- Panel
- 0.96" SSD1306
Builds only — never run on hardware
Heltec Wireless Stick V2/V2.1
heltec-ws- MCU
- ESP32: 8 MB flash
- Radio
- SX1276
- Panel
- 0.49" 64x32 SSD1306 on Vext
Verified on hardware
Heltec Wireless Bridge
heltec-wb- MCU
- ESP32-D0WDQ6: 8 MB flash, 8 MB PSRAM
- Radio
- SX1276
- Panel
- — (headless)
Verified on hardware
Heltec WiFi LoRa 32 V3
heltec-v3- MCU
- ESP32-S3: 8 MB flash, no PSRAM
- Radio
- SX1262 (TCXO, DIO2 drives the RF switch)
- Panel
- 0.96" SSD1306 on the switched Vext rail
Verified on hardware
Heltec Wireless Paper
heltec-wp- MCU
- ESP32-S3: 8 MB flash, no PSRAM
- Radio
- SX1262 (TCXO, DIO2 drives the RF switch)
- Panel
- 2.13" e-ink (250x122, E0213A367), driven
Verified on hardware
Heltec V4 (TFT)
heltec-v4- MCU
- ESP32-S3: 16 MB flash, 2 MB PSRAM in package
- Radio
- SX1262 (TCXO, DIO2 drives the RF switch) behind a GC1109 or KCT8103L front end
- Panel
- 2.4" 240x320 ST7789 with a CHSC6X touch layer
Verified on hardware
LilyGO T-Deck
t-deck- MCU
- ESP32-S3: 16 MB flash, 8 MB octal PSRAM in package
- Radio
- SX1262 (TCXO at 1.8 V, DIO2 drives the RF switch), no amplifier
- Panel
- 2.8" 320x240 ST7789 with a GT911 touch layer
Verified on hardware
Elecrow ThinkNode M9
thinknode-m9- MCU
- ESP32-S3: 16 MB flash, 8 MB octal PSRAM in package
- Radio
- Semtech LR1110 (TCXO at 3.3 V, the chip drives its own antenna switch from DIO5/DIO6)
- Panel
- 2.4" 320x240 ST7789, no touch layer
Verified on hardware